Emcore

emcore_logoweb-150x31
Emcore- Fiber Optic Links: Broadband RF, L-band, Base Band A/V & DVB-ASI

Emcore Optiva Platform – Removing the Growing Pain

As the requirement for more centralization within teleports continues to grow and the pressure to reduce operational cost increases, more and more companies are looking at fiber optics as an alternate solution to RF over coax/copper to connect their Remote Antenna Farm to their Central Operations Room. Although the benefits are very tangible, justification of this capital investment must be made and as such, making a system that is completely scalable over time is a critical consideration. Emcore developed the Optiva Platform to address these concerns and allow your fiber network architecture to grow seamlessly as your requirements grow.


Emcore CoolHub Outdoor Enclosure for Optiva Products

EMCORE’s CoolHub Outdoor Enclosure provides power and environmental protection for up to 16 Optiva transmitters & receivers for RF, Video, Data and Ethernet. With a weather-tight seal and all the necessary internal connections and mounting hardware, the CoolHub may be placed directly at the antenna site to provide greater flexibility in design.


Emcore Optiva OTS-2 Q/V-Band 60GHz Unamplified

The Optiva OTS-2 Q/V-Band 60 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 50 MHz to 60 GHz frequency range for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high-dynamic-range applications.


Emcore Optiva Next-Gen OTS 1LNG 3GHz/ 6GHz

The Optiva OTS-1LNG 3 GHz/6 GHz 1310 nm Wideband Fiber Optic Link is a Next-Gen L-Band fiber optic link optimized to provide transpar-ent IF, extended L-Band, C- and S-Band signal transport and to perform in the 50 MHz to 6 GHz frequency range for satellite antenna and interfacility applications.


Emcore OTP-4DJ

The Optiva OTP-4DJ provides for the transmission of 4 channels of RS-422 duplex serial data, over long or short distances, using a single fiber.

 


Emcore OTP-1DVI2A1UKM (up to 3840×2160)

The Optiva OTP-1DVI2A1UKM provides for the transmission of uncompressed DVI, VGA or Component (RGB / RGBHV / YPbPr) video, stereo analog audio, with USB KVM over long or short distances, using Dual-Link DVI-D and 10 Gbps Optics, up to 3840×2160 @ 30 Hz and 2560×1600 @ 60 Hz.


Emcore OT-DTCR 1- or 2-Slot Enclosures

The Optiva Desk Top Card Racks (DTCR) are ruggedized aluminum-housing units that accept any Optiva insert card. The 1-slot (OT-DTCR-1) and 2-slot (OT-DTCR-2) enclosures both use an external PS-9012 wall-mount power supply and have a 2-pin Phoenix power connector option for more custom applications.

 



Emcore Optiva OT-CC-16F Fan-Cooled16 Slot Enclosure

The Optiva OT-CC-16F 3 RU 19” rack-mount, fan-cooled enclosure is a ruggedized aluminum housing unit that accepts any Optiva insert card. This 16-slot chassis provides a state-of-the-art platform for density and space utilization. A wide variety of Optiva cards have been developed for this platform including RF and microwave fiber optic transmitters and receivers, optical amplifiers, RF and optical passive devices, video, audio, data, and Ethernet products.


Emcore Optiva OT-CC-6-1U Fan-Cooled 6-Slot Enclosure

The Optiva OT-CC-6 1 RU 19” rack-mount, fan-cooled enclosure is a ruggedized aluminum housing unit that accepts any Optiva insert card. This high-capacity 6-slot chassis provides a state-of-the-art platform for density and space utilization. A wide variety of Optiva cards have been developed for this platform including RF and microwave fiber optic transmitters and receivers, optical amplifiers, RF and optical passive devices, video, audio, data, and Ethernet products.

 


Emcore Optiva PS-200F Watt Universal Power Supply AC/DC

The PS-200F 200 Watt Universal Power Supply built to function within the Optiva OT-CC-16F 19” 3 RU rack-mount enclosure. Each chassis is designed to accommodate up to two redundant PS-200F units. Three AC models are available. PS-200F-NA includes a North American power cord, PS-200F-EU includes a European power cord and PS-200F-UK includes a United Kingdom power cord. A single DC model is also available, PS-200F-DC. All units are hot-swappable, come in an insert card form-factor and operate at either an input voltage of 90-264 VAC or +24 – +48 VDC. The PS-200F is cooled using an internal fan and its rugged ergonomic design and wide temperature range are geared for industrial applications.


Emcore OTS-1 REF-10

The Optiva OTS-1 Ref-10 Reference Oscillator Link is optimized for the transport of 10 MHz high-level reference signal input. It features low phase noise and high-dynamic-range, with optically-isolated DFB lasers that run cool and have low power consumption requirements. Optiva Reference Oscillator Links are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore Optiva OTS-1 REF-5

The Optiva OTS-1 Ref-5 Reference Oscillator Link is optimized for the transport of 5 MHz high-level reference signal input. It features low phase noise and high-dynamic-range, with optically-isolated DFB lasers that run cool and have low power consumption requirements. Optiva Reference Oscillator Links are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore Optiva OTS-1 REF-1

The Optiva OTS-1 Ref-1 Reference Oscillator Link is optimized for the transport of 1 MHz high-level reference signal input. It features low phase noise and high-dynamic-range, with optically-isolated DFB lasers that run cool and have low power consumption requirements. Optiva Reference Oscillator Links are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore OTS-1L2 3 GHz

Optiva Dual Wideband Fiber Optic Links are optimized to perform in the 50 MHz to 3 GHz frequency range providing transparent signal transportation for satellite antenna applications. The OTS-1L2 is a dual RF fiber optic link that accepts two RF inputs and provides two RF outputs with a single plug-in pair. This dual-density card increases the chassis capacity by a factor of two.

 


Emcore OTS-1LC 3 GHz

The Optiva OTS-1LC CWDM Wideband Fiber Optic Link is optimized to provide transparent IF, L- and S-Band signal transport and to perform in the 50 MHz to 3 GHz frequency range for satellite antenna and interfacility applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) to provide multiple frequency transport in a single flexible platform.

 


Emcore OTS-1LT1 3 GHz

The Optiva OTS-1LT1 Wideband Fiber Optic Link is optimized to provide transparent IF, L- and S-Band signal transport and to perform in the 50 MHz to 3 GHz frequency range for satellite antenna and interfacility applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) to provide multiple frequency transport in a single flexible platform.

 


Emcore Optiva OTS-1LT 3 GHz

The Optiva OTS-1L 1310 nm Wideband Fiber Optic Link is optimized to provide transparent IF, L- and S-Band signal transport and to perform in the 50 MHz to 3 GHz frequency range for satellite antenna and interfacility applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) to provide multiple frequency transport in a single .exible platform.

 


Emcore Optiva OTS-2 18 GHz Amplified

The Optiva OTS-2 18 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 50 MHz to 18 GHz frequency range for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high-dynamic-range applications. Optiva microwave band transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.


Emcore Optiva OTS-2 18 GHz Unamplified

The Optiva OTS-2 18 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 50 MHz to 18 GHz frequency range for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high dynamic-range applications. Optiva microwave band transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple
signal formats and frequency bands in a single flexible platform.


Emcore Optiva OTS-2 40 GHz Amplified

The Optiva OTS-2 40 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 50 MHz to 40 GHz frequency range for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high dynamic- range applications. Optiva microwave band transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.


Emcore 5200-Series_3-GHz

The 5200 Series 3 GHz Fiber Optic Inter-Facility Link (IFL) is a high-performance, cost-effective alternative to coaxial cable for 50 MHz to 3000 MHz communications applications. EMCORE’s fiber optic IFLs function as transparent RF fiber links. These IFLs eliminate the limitations of copper systems by enabling longer transmission distance while retaining the highest level of signal quality. In addition, EMCORE’s fiber optics provide several other significant network advantages, including simplified network design, ease of installation, and immunity from EMI/RFI and lightning.


Emcore Optiva OTS-2 40 GHz Unamplified

The Optiva OTS-2 40 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 50 MHz to 40 GHz frequency range for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high dynamic-range applications. Optiva microwave band transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore OTS-2 22 GHz Unamplified

The Optiva OTS-2 22 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 50 MHz to 22 GHz frequency range for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high dynamic-range applications. Optiva microwave band transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore OTS-2 22 GHz Amplified

The Optiva OTS-2 22 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 50 MHz to 22 GHz frequency range for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high-dynamic-range applications. Optiva microwave band transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore Optiva OTS-2 X-Band

The Optiva OTS-2 X-Band transmitter and receiver are ideal to construct 7.000 to 10.000 GHz transparent fiber optic links for antenna remoting, electronic warfare systems, broadband delay lines, signal
processing systems and other high-dynamic-range applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore Optiva OTS-2 DBS

The Optiva OTS-2 DBS transmitter and receiver are ideal to construct 17.300 to 18.400 GHz transparent fiber optic links for antenna remoting, electronic warfare systems, broadband delay lines, signal processing systems and other high-dynamic-range applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore OTS-2 Ku-Band

The Optiva OTS-2 Ku-Band transmitter and receiver are ideal to construct downlink 10.700 to 12.750 GHz and uplink 13.750 to 14.500 GHz transparent fiber optic links for antenna remoting, electronic
warfare systems, broadband delay lines, signal processing systems and other high-dynamic-range applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport ofmultiple signal formats and frequency bands in a single flexible platform.

 


Emcore OTS-2 Ka-Band

The Optiva OTS-2 Ka-Band transmitter and receiver are ideal to construct downlink 18.300 to 21.200 GHz and uplink 28.350 to 31.000 GHz transparent fiber optic links for antenna remoting, electronic
warfare systems, broadband delay lines, signal processing systems and other high-dynamic-range applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore Optiva OTS-IRG Fiber Optic Intra-Facility Links

Optiva OTS-IRIG (Inter-Range Instrumentation Group) B000 / 1 PPS (Pulse Per Second) Fiber Optic Intra-Facility links provide for simultaneous transmission of IRIG-B000 and 1PPS, or one signal each over fiber. These high-performance links feature low jitter and sharp rise and fall times. Optiva IRIG Links are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 


Emcore OTS-1 REF-400

The Optiva OTS-1 Ref-400 Reference Oscillator Link is optimized for the transport of 400 MHz high-level reference signal input. It features low phase noise and high-dynamic-range, with optically-isolated DFB lasers that run cool and have low power consumption requirements. Optiva Reference Oscillator Links are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 

 


Emcore OTS-1 REF-100

The Optiva OTS-1 Ref-100 Reference Oscillator Link is optimized for the transport of 100 MHz high-level reference signal input. It features low phase noise and high-dynamic-range, with optically-isolated DFB lasers that run cool and have low power consumption requirements. Optiva Reference Oscillator Links are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as other Optiva cards to support transport of multiple signal formats and frequency bands in a single flexible platform.

 

 


Emcore 5200 Series 6.5 Ghz

The 5200 Series 6.5 GHz Fiber Optic Inter-Facility Link (IFL) is a high-performance, cost-effective alternative to coaxial cable for 20 MHz to 6500 MHz communications
applications. EMCORE’s fiber optic IFLs function as transparent RF fiber links. These IFLs eliminate the limitations of copper systems by enabling longer transmission distance
while retaining the highest level of signal quality. In addition, EMCORE’s fiber optics provide several other significant network advantages, including simplified network design, ease of installation, and immunity from EMI/RFI and lightning.


Emcore OTS-1LS 2.5 GHz

The Optiva OTS-1LS 1310/1550 nm Wideband Fiber Optic Link is optimized to provide transparent IF, L- and S-Band signal transport and to perform in the 50 MHz to 2.5 GHz frequency range for satellite
antenna and interfacility applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) as Optiva HD video, audio, serial data, and USB extension / distribution cards to provide multiple format and frequency transport in a single flexible platform.

 


Emcore Optiva OTS-1LD 2.5 GHz

The Optiva OTS-1LD DWDM Wideband Fiber Optic Link is optimized to provide transparent IF, L- and S-Band signal transport and to perform in the 50 MHz to 2.5 GHz frequency range for satellite antenna and interfacility applications. Optiva satellite and microwave transmitters and receivers are SNMP compliant. They can be housed in the same chassis and monitored by the same Network Management System (NMS) to provide multiple frequency transport in a single flexible platform.

 


2990pro

Emcore 2990PRO

The Emcore/Force Model 2990PRO L-Band Satellite Fiber Optic Transport System provides an economical solution for transporting digital signals for numerous satellite distribution applications, including headend relocation, and distribution of digital broadcast systems (DBS). The Emcore 2990PRO utilizes a cost-effective coax cabling configuration to distribute the RF signals from the dish to the transmitter and from the receiver to the headend.


medallion_7200

Emcore Medallion 7200 series

The Emcore Medallion 7200 series product line is a family of state-of-the-art high performance CATV Erbium/Ytterbium Doped Fiber Amplifiers (EYDFA). Packaged in a convenient 2 RU housing, this line of fiber amplifiers has been optimized for superior output power stability and the exceptionally low noise figures demanded by CATV applications.


medallion_7100

Emcore Medallion 7100 Series

The Emcore Medallion 7100 series product line is a family of state-of-the-art high performance CATV Erbium Doped Fiber Amplifiers (EDFA). Packaged in convenient 1 RU housing, this line of fiber amplifiers has been design optimized for superior output power stability and the exceptionally low noise figures demanded by CATV applications.


vx

Emcore VX-1DVI

The VX-1DVI-SD optical extender is a single fiber DVI extender that can send 1 channel of DVI video, 1 channel of serial data and 2 channels of analog audio (with adapter) up to 6.2 miles (10 km). The extender is a low profile unit that transports over standard multimode or singlemode fiber using LC type optical connectors for a secure cable connection. LC connectors are the smallest and most widely used type. This allows the easiest installation possible through conduit or wall/ceiling mounted boom arms.

Graphic resolutions up to 1920×1200 and video resolutions up to 1080p 60Hz are possible over a single fiber. Both video and data can be extended out to 6 miles without the need for distribution amplifiers, cable equalization or in-line repeaters that are normally associated with copper cable extension. The VX- 1DVI-SD is the most economical solution for sending a single channel of digital video with data and audio over long distances.

No more EDID learning or blanked out screens! Critical EDID information is read directly from the monitor and passed to the graphics card via the duplex data channel. The VX-1DVI-SD can work on any digital display and provide resolutions up to 1920×1200. The VX-1DVI-SD is also HDCP compliant allowing the exchange of keys between the source and display. Copyrighted material can be sent over the fiber link.


opg-1l

Emcore OPG-1L Series

The Emcore OPG-1L series RF fiber optic links are designed for the openGear® platform standard and are optimized to perform in the 50 MHz to 2.3 GHz frequency range for IF- and L-Band video signals up to 30 km. They provide transparent signal transport between broadcast or cable network antenna facilities and control room terminal equipment.


medallion_6000

Emcore Medallion 6000 Series

The Emcore Medallion 6000 series is a family of state-of-the-art high-performance 1550 nm externally-modulated CATV fiber optic transmitters optimized for varying network applications. Packaged in convenient 1 RU housing, this line of optical transmitters couples high optical output powers, up to 11.0 dBm, with low optical linewidth resulting in unmatched performance. The optical modulator, combined with proprietary pre-distortion circuitry, provides superior CTB and CSO performance with SBS suppression levels of greater than 21 dBm. Advanced features such as built-in field adjustable SBS control and electronic dispersion compensation allow these transmitters to be quickly optimized in the field for any link or application without the need to procure specifically tuned transmitters. This affords the system designer a level of flexibility previously unknown in the CATV market place.


 

medallion_2100

Emcore Medallion 2100

The Emcore Medallion 2100 Optical A/B Switch is a high-performance solution for network protection and optical redundancy. Packaged in convenient 1 RU housing, this line of optical switches provides an automatic or manual fiber switching function to protect the network from inadvertent service outages due to up-stream optical signal degradation. Each fiber’s optical signal power level is continuously monitored, as is an adjustable optical trip threshold for each channel. If the primary fiber’s optical signal power level falls below the desired optical trip threshold, the unit automatically switches to the secondary fiber, thus eliminating the need for intervention of a system operator. The Medallion 2100 is capable of manual switching or can be switched remotely via SNMP or via a WEB browser adding optical protection to many system applications.